Amount Of Copper Research Articles

The Waelz Slag from Electric Arc Furnace Dust Processing: Characterization and Magnetic Separation Studies

The Waelz slag generated during electric arc furnace dust processing is an iron-rich product with significant amounts of iron, zinc and copper. About 600–800 kg of the Waelz slag is generated per ton of the dust processed. The Waelz slag samples from two different plants were thoroughly characterized using inductively coupled plasma optical emission spectroscopy (ICP-AES), X-ray diffraction analysis (XRD), chemical phase analysis, Mössbauer spectroscopy and other supporting methods. The phase distribution of iron, zinc and copper was determined in the Waelz slag samples. Low-intensity wet magnetic separation was tested for the iron recovery from the Waelz slag samples. It was found that the Waelz slag samples have complex chemical and mineralogical compositions, which can impede the selective recovery of valuable elements. The obtained results indicate that the chemical and mineralogical composition of the Waelz slag samples has a considerable effect on the magnetic separation indexes. The experiments showed that the iron concentrates with Fe contents of 73% and 46.8% with the metallization degrees of 87.2% and 57.5% and the iron recovery degree of 54.8% and 52.9% were obtained at optimal conditions for two different samples, respectively, without selective segregation of Cu and Zn in the magnetic or non-magnetic fraction.

Evaluating the ATR-SEIRAS Performance of Electrodeposited Copper CO2 Reduction Catalysts using a Flow-Through Spectroelectrochemical Cell

The ATR-SEIRAS (attenuated total reflection surface enhanced infrared absorption spectroscopy) activity of electrodeposited Cu nanoparticles on indium tin oxide (ITO)-modified Si internal reflection elements is reported. The solution in the cell is easily, and repeatedly, exchanged between a copper deposition bath and a solution containing 4-methoxypyridine through the use of a flow-through spectroelectrochemical cell. 4-methoxypyridine is a convenient SEIRAS probe molecule exhibiting potential dependent adsorption/desorption on the copper surface. Successive amounts of copper are deposited and then evaluated for electrochemical SEIRAS activity without the need to expose the Cu surface to ambient conditions. It is found that copper deposition charge densities of approximately 60 mC cm-2 exhibit the largest amplitude and most symmetric IR absorption peaks of the investigated electrodeposition conditions. SEM images of the different Cu charge density films are correlated with the SEIRAS results and establish that close-packed two-dimensional, percolated arrays of oblate, ellipsoidal Cu nanoparticles are responsible for ideal SEIRAS performance and three-dimensional aggregates of larger particles should be avoided. Textured films of Cu nanoparticles are used to determine the adsorbed species present on the copper surface during CO2 electroreduction at low overpotentials. Evidence of adsorbed CO and COH is found at lower overpotentials than those described in previous reports.

Surface nanostructuring of Ti40Cu40Zr11Fe3Sn3Ag3 amorphous alloy by alkaline chemical treatment for potential use as a biocompatible material

Amorphous alloys show potential as implant materials due to their superior mechanical properties and good corrosion resistance. However, the presence of toxic elements in the alloy composition can pose challenges, as they can react with the surrounding tissue, leading to inflammation and cell death. To address this, Ti40Cu40Zr11Fe3Sn3Ag3 at% amorphous alloy is developed. This composition comprises of biocompatible elements (Ti, Zr, and Sn) and antimicrobial elements (Ag, Fe, and Cu), for potential use as implant materials. Chemical pseudo-dealloying using a solution of ammonium hydroxide and hydrogen peroxide is employed to selectively remove copper from the sample surface, which may induce toxicity by prolonged contact, and promote the formation of a patterned passivating Ti/Zr oxide-rich surface to enable possible antimicrobial effects. The surface of the samples was analyzed using atomic force microscopy, scanning electron microscopy, and X-ray photoelectron spectroscopy. The modified surfaces show titanium oxide-rich nanostructured topography with depleted amounts of copper from the surface. The kinetics of the selective removal of copper, and the influence of parameters such as electrolyte concentration, immersion time, and stirring velocity on the evolution of morphology were investigated. Our findings elucidate the mechanism of pseudo-dealloying using an ammonia-based solution and demonstrate its efficacy in enhancing the biocompatibility of the alloy. In detail, the pseudo-dealloyed samples exhibited hydrophilic interactions and demonstrated hemocompatibility, making them promising candidates for blood-contacting medical devices. This study underscores the significance of our approach in tailoring the surface properties of amorphous alloys for biomedical applications, paving the way for their utilization in implant materials with improved biocompatibility.

Accumulation of Mn, Cu, and Zn in Flowers and Leaves of Catalpa bignonioides in an Urban Area Under Climate Change Conditions

Abstract Green areas are an important part of the urban landscape. Trees produce oxygen, provide shade, maintain soil moisture, and reduce the amounts of toxic gases and dust in the air. Due to the changing climate, species characteristic of other climatic zones, e.g. Catalpa bignonioides, are planted in urban parks in Poland, mainly due to the attractive appearance of the leaves and flowers. The aim of the study was to assess the content of Mn, Cu, and Zn in flowers and leaves of C. bignonioides in the urban park and to determine the value of bioconcentration coefficients (BCF) of these metals. The obtained results indicate that the flowers and leaves of C. bignonioides accumulate lesser amounts of manganese, copper, and zinc. It is a consequence of the limited bioavailability of these components in soils, due to too high pH values resulting from alkalinization of urban soils. The values of bioconcentration coefficients (BCF <1) confirm the low accumulation of Mn, Cu, and Zn in both leaves and flowers of C. bignonioides, due to the limited mobility of manganese, copper, and zinc compounds in the soils of the urban park and the low impact of falling dusts, which are the carriers of the analyzed components.

Comparison of insecticide sprays in alternate rows and in all rows on Asian citrus psyllid control and Huanglongbing progress in sweet orange orchards.

One strategy to reduce Huanglongbing (HLB) is controlling its insect vector, the Asian citrus psyllid (ACP) Diaphorina citri, by preventive insecticide sprays. The recommendation is to spray insecticide in all rows (conventional spray - CONV), but some growers empirically spray in alternate rows (ALT) to increase the spray frequency without increasing the operating cost. Therefore, this work compared the effect of ALT with CONV on the ACP population and HLB incidence. The spray deposition (amount of metallic copper per leaf area), coverage (percentage of water-sensitive paper area covered by spray), and efficacy (ACP mortality) of each treatment were also evaluated on both sides of the trees. Two field trials were performed: Trial #1 compared ALT every 7 days (ALT7) with CONV every 14 days (CONV14), and trial #2 compared different spray frequencies of ALT with CONV every 7 days (CONV7). In trial #1, no differences were observed in the ACP population or HLB progress between ALT7 and CONV14 after 5 years. In trial #2, ALT7 presented the highest percentage of ACP and cumulative HLB incidence than CONV7 and ALT every 3 to 4 days, after 2 years. Hence, when the frequency of ALT was half the frequency of CONV, similar results were observed. Spray deposition, coverage, and efficacy were similar between tree sides in CONV, but they were uneven in ALT, resulting in higher values on the tree side that directly received the spray. Insecticide spray should be performed with the frequency enough to keep new shoot protected during their growth.

Prehistoric and Early Roman Period Goldwork from Northwestern Iberia: An Analytical Study of Artefacts from the Archaeological and Historical Museum of A Coruña

This article presents the results of a topographical and analytical study using hh-XRF of 22 gold and gilded objects from the Archaeological and Historical Museum of A Coruña (Galicia, Spain). They are highly representative of the northwestern Iberian goldwork from the Chalcolithic (third millennium BC) to the early Roman period (first century AD). This study contributes to our knowledge of the production techniques used in those periods, as well as their evolution over time. The collection includes some of the most representative types in this area, such as Early Bronze Age “sheet collars” and torcs from the Second Iron Age. In the case of torcs, new data are provided on one of the formally best-documented types (the Artabrian type) and on those known as “Baroque torcs” that are characteristic of the final moments of this goldsmith tradition. While pieces from the Chalcolithic and Early Bronze Age were made with alluvial gold, the torcs from the Late Iron Age contain variable amounts of silver and copper. Also detected is the frequent use of cores made of less precious metals, which were subsequently given a golden appearance using gilding techniques. The new data are discussed in light of our current knowledge of NW Iberian goldwork, one of the most representative of this craft tradition in Western Europe for those periods.

A NOVEL HYBRID DECISION-MAKING MODEL: FUZZY AHP-TOPSIS APPROACH FOR PRIORITISING COPPER SMELTING PROCESSES

The construction of a copper smelting facility and its undisturbed and profitable business undoubtedly contribute to the development of each country’s economy. These facilities employ many workers and produce a large amount of copper, reducing imports and dependence on this important raw material, thereby improving the economic situation in a given country. More than a hundred copper smelters operate worldwide, many of which use different types of copper extraction processes. Strict legislation relating to ecology and environmental protection as well as stakeholder involvement in selecting and constructing copper smelting facilities limit the maximisation of short-term economic objectives. The prioritisation of technological processes for the extraction of copper must consider the impacts of often mutually opposing economic, technical and environmental objectives. No research from the available literature analyses the economic, technical and environmental parameters systematically. Studies have mainly dealt with exploring individual influences of factors through the use of one selection method. This paper presents the development of a novel hybrid AHP-TOPSIS model in fuzzy environments that will provide both informative decisions and optimum results of decision making.

PROCESSING OF COPPER ELECTROLYTE FOR ZINC-CONTAINING PRODUCT

Abstract. Waste solutions from the electrolytic production of copper contain significant amounts of copper and nickel sulfates, sulfuric acid, arsenic and other components of the copper electrolyte. The processing of such solutions is considered in this work not only from the point of view of environmental protection, but also in terms of extracting various valuable components from the electrolyte into commercial products. A thermodynamic analysis of the interactions between barium and arsenic, as well as their compounds in the Ba(AsO2)2-Ba3(AsO4)2-H2O system was carried out based on the E-pH diagram. The possibility of using barium compounds as a precipitant for arsenic from copper electrorefining solutions has been demonstrated. The efficiency of removing arsenic (more than 84%) from the electrolyte using barium oxide in the form of sparingly soluble barium arsenate has been established. By adding calculated amounts of zinc oxide into the working solution, it is possible to form solutions containing certain concentrations of Cu, Ni, and Zn. By further adding zinc oxide into the solution, its deep dehydration was achieved. The resulting copper-nickel-zinc and nickel-zinc solutions are the raw material for producing non-ferrous metal alloys using the electromembrane method.
  
  
  

Exploring Cu-Doped Co3O4 Bifunctional Oxygen Electrocatalysts for Aqueous Zn-Air Batteries.

The efficiency of oxygen electrocatalysis is a key factor in diverse energy domain applications, including the performance of metal-air batteries, such as aqueous Zinc (Zn)-air batteries. We demonstrate here that the doping of cobalt oxide with optimal amounts of copper (abbreviated as Cu-doped Co3O4) results in a stable and efficient bifunctional electrocatalyst for oxygen reduction (ORR) and evolution (OER) reactions in aqueous Zn-air batteries. At high Cu-doping concentrations (≥5%), phase segregation occurs with the simultaneous presence of Co3O4 and copper oxide (CuO). At Cu-doping concentrations ≤5%, the Cu ion resides in the octahedral (Oh) site of Co3O4, as revealed by X-ray diffraction (XRD)/Raman spectroscopy investigations and molecular dynamics (MD) calculations. The residence of Cu@Oh sites leads to an increased concentration of surface Co3+-ions (at catalytically active planes) and oxygen vacancies, which is beneficial for the OER. Temperature-dependent magnetization measurements reveal favorable d-orbital configuration (high eg occupancy ≈ 1) and a low → high spin-state transition of the Co3+-ions, which are beneficial for the ORR in the alkaline medium. The influence of Cu-doping on the ORR activity of Co3O4 is additionally accounted in DFT calculations via interactions between solvent water molecules and oxygen vacancies. The application of the bifunctional Cu-doped (≤5%) Co3O4 electrocatalyst resulted in an aqueous Zn-air battery with promising power density (=84 mW/cm2), stable cyclability (over 210 cycles), and low charge/discharge overpotential (=0.92 V).

Microstructure analysis of 7050 aluminum alloy joint fabricated by linear friction weld

The microstructure of a linear friction welded joint of 7050 aluminum alloy was investigated through optical microscopy (OM), scanning electron microscopy (SEM), and electron backscatter diffraction (EBSD). The analysis focused on grain boundary types, microstructure, and mechanical properties of the joint. The results reveal that fine equiaxed crystals are generated in the welded zone through dynamic recrystallization. The average grain size is 6.8 μm, with a volume fraction of large angle grain boundaries reaching 69.5%. The microstructure primarily consists of Cube {001}<100> texture, {111}<110> Brass recrystallization texture, and a small amount of copper {112}<111> deformation texture. The thermo-mechanically affected zone (TMAZ) presents a linear structure with an average grain size of 15.8 μm and a volume fraction of 36.1% at large grain boundary, resulting in a deformed Brass {011}<211> texture and a small amount of {236}<385> as well as {111}<110> Brass recrystallization texture. The welded joint exhibits a tensile strength of 492 MPa and a yield strength of 380 MPa, which represents 94.2% and 78.5% of the base material, respectively. Furthermore, the elongation of the joint is 10.2% and 98% of the base material, respectively. The fracture of the tensile sample is observed in the TMAZ, showing good mechanical properties with a mixed fracture mode with some degrees of ductility and brittleness.

Selective dissolution of zinc and lead from duplex β-phase brasses in low and high conductivity water

This study provides insights regarding the selective metal leaching of brass in various tap water conditions, which benefits water utilities to predict the potential of metal released from brass water meters. The long-term time-dependent selective metal dissolution of brass with various β phase fractions have not previously been investigated. In this study, a 201-d immersion experiment was carried out in low and high conductivity tap water (LCTW and HCTW, respectively). Three commercialized brass samples in different β phase fractions (β = 51%, β = 43%, β = 39%), named brass 51, brass 43, and brass 39, respectively, were used. The results showed that brass 51 had the most negative corrosion potential (−0.17 V) and the lowest polarization resistance (8.5 kΩ) compared to brass 43 and brass 39 (−0.04 V and 10.1−14.7 kΩ, respectively) in LCTW. This trend was verified by the 201-d immersion experiment in which brass 51 exhibited the highest zinc leaching rate (21−30 μg L−1 cm−2 d−1), followed by brass 43 and brass 39 (16−23 μg L−1 cm−2 d−1) in both waters. The leaching amounts of lead and copper were extremely low compared to zinc. In LCTW, the uniform corrosion (UC) mechanism dominated from day 1 to day 120. Afterwards, UC was replaced by the galvanic corrosion (GC) mechanism, with the selective leaching coefficient of Zn over Cu (SZn/Cu) increasing from 10 to 25 to 40−80. In HCTW, however, the SZn/Cu reached 300−1000, and the transition of UC to GC occurred earlier on day 30 due to the rapid formation of the ZnO layer on the brass surface that hindered the ion attack.

The effect of copper reduction on the control of downy mildew in Mediterranean grapevines

AbstractThe application of copper-based fungicides has led to the problematic accumulation of copper in the soil of many European vineyards. In this work, we tested the effectiveness of downy mildew control strategies that considerably reduce the amount of copper, through the application of other non-toxic compounds. The study took place in three different regions of Catalonia, by combining smaller and larger-scale trials for two growing seasons. Although variations among experiments were detected, the treatments used here may reduce the applied copper content by up to 77 percent. The cooper reduction-strategies, which alternated standard copper application of copper oxychloride with applications of products based on Equisetum arvense L., or with applications of products with heptagluconic acid (an alternative formulation with a very low-rate of copper), provided the most consistent protection against downy mildew. Moreover, these treatments reduced copper inputs by 63 and 47 percent as compared to conventional treatments based on repeated applications of copper oxychloride. This work underlines the possibility of reducing the amount of copper applied to control downy mildew in Mediterranean vineyards, through the use of newly-developed formulations.

Nitrate modulates the physiological tolerance responses of the halophytic species Sarcocornia fruticosa to copper excess

Coexistence impact of pollutants of different nature on halophytes tolerance to metal excess has not been thoroughly examined, and plant functional responses described so far do not follow a clear pattern. Using the Cu-tolerant halophyte Sarcocornia fruticosa as a model species, we conducted a greenhouse experiment to evaluate the impact of two concentration of copper (0 and 12 mM CuSO4) in combination with three nitrate levels (2, 14 and 50 mM KNO3) on plant growth, photosynthetic apparatus performance and ROS-scavenging enzymes system. The results revealed that S. fruticosa was able to grow adequately even when exposed to high concentrations of copper and nitrate. This response was linked to the plant capacity to uptake and retain a large amount of copper in its roots (up to 1500 mg kg−1 Cu), preventing its transport to aerial parts. This control of translocation was further magnified with nitrate concentration increment. Likewise, although Cu excess impaired S. fruticosa carbon assimilation capacity, the plant was able to downregulate its light-harvesting complexes function, as indicated its lowers ETR values, especially at 12 mM Cu + 50 mM NO3. This downregulation would contribute to avoid excess energy absorption and transformation. In addition, this strategy of avoiding excess energy was accompanied by the upregulation of all ROS-scavenging enzymes, a response that was further enhanced by the increase in nitrate concentration. Therefore, we conclude that the coexistence of nitrate would favor S. fruticosa tolerance to copper excess, and this effect is mediated by the combined activation of several tolerance mechanisms.

Establishment of Indirect Competitive Enzyme-linked Immunosorbent Assay (ic-ELISA) for Copper ion (Cu2+) in Raw Meat Products

Adding an appropriate amount of copper to feed can promote the growth and development of livestock; however, a large amount of heavy metal copper can accumulate in livestock through the enrichment effect, which poses a serious threat to human health. Traditional Cu2+ detection relies heavily on complex and expensive instruments, such as inductively coupled plasma-optical emission spectrometry (ICP-OES) and inductively coupled plasma-mass spectrometry (ICP-MS); thus, convenient and simple rapid detection technologies are urgently needed. In this paper, synthesized copper antigens were used to immunize mice and highly specific anticopper monoclonal antibodies were obtained, which were verified to exhibit high affinity and specificity. Based on the above antibodies, an indirect competitive enzyme-linked immunosorbent assay (ic-ELISA) was established for the rapid detection of copper content in pork. The standard inhibition curve of the method was obtained by antigen–antibody working concentration screening, in which the half inhibitory concentration (IC50) was 11.888 ng/mL, the limit of detection (LOD) was 0.841 ng/mL and the correlation coefficient R2 of the curve was 0.998. In the additive recovery experiment, the recovery rate ranged from 90% to 110%, and the coefficient of variation (CV) was less than 10%, indicating that the method achieved high accuracy and precision. Finally, the results of ic-ELISA combined with Bland-Altman analysis showed a high correlation with ICP-MS, and the correlation coefficient (R2) reached 0.990 when the copper concentration was less than 200 ng/mL. Thus, the ic-ELISA method exhibits high reliability.

Effective chloramine management without “burn” in biofilm affected nitrifying tanks using a low dose of copper

This paper highlights the potential to effectively inhibit nitrification and restore chloramine levels using a low copper concentration in a biofilm-affected (surface-to-volume ratio 16 m−1) continuous-flow laboratory-scale chloraminated system. High nitrite and low chloramine containing tanks are always recovered with chlorine “burn” by water utilities. The “burn” is not only costly and operationally complex, but also compromises the water quality, public health, and customer relations. A laboratory system comprising five reactors connected in series was operated. Each reactor simulated conditions typically encountered in full-scale systems. Low amount of copper (0.1–0.2 mg-Cu L−1) was dosed once per day into nitrified reactors. At any given time, only one reactor was dosed with copper. Not only inhibition of nitrification, chloramine decay associated with bulk water, biofilm and sediments also improved. However, the improvement was quicker and more significant when the influent to the reactor contained a high chloramine and a low nitrite concentration. Ammonia oxidising microbes exhibited resilience when exposed to low copper and chloramine concentrations for an extended period. Chloramine decay due to planktonic microbes and chemical reactions in bulk water decreased more rapidly than decay attributed to biofilm and sediments. The concept “biostable residual chlorine” explained how copper and chloramine can inhibit nitrification. Once nitrification was inhibited, the chloramine supplied from upstream effectively continued to suppress downstream nitrification, and this effect lasted more than 50 days even at 22 °C. The findings could be used to develop short-term copper dosing strategies and prevent negative impacts of nitrification and breakpoint chlorination.

Evaluation of metal ions and DNA recovery from the surface of fired and unfired brass ammunition to improve STR profiling.

Interest in recovering DNA from the surface of ammunition evidence for genotyping has increased over the past few years. Numerous studies have examined a variety of methods to maximize DNA recovery from these types of challenging samples, but successful DNA profiling has been inconsistent. Low amounts of DNA and PCR inhibition due to metal ions have been suggested as the leading causes of poor results; however, no study quantitatively examined the presence of metal ions at various stages of the DNA analysis workflow from DNA collection through to amplification. In this study, the effectiveness of six different DNA collection and purification methods commonly used by forensic laboratories to process brass ammunition for DNA evidence was investigated. The amount of copper, zinc, and other metals co-recovered from fired and unfired brass casings during DNA collection (using numerous soaking, swabbing, and direct PCR protocols) was quantified via Inductively Coupled Plasma - Optical Emission Spectrometry (ICP-OES). This same panel of metals was subsequently quantified after DNA lysis and purification steps. Results demonstrated that low amounts of DNA, DNA damage, and degradation are more detrimental to STR typing results than PCR inhibition, as metal ions were successfully removed by all DNA purification methods tested. Furthermore, the use of metal ion chelators increased the amount of DNA recovered and number of reportable STR alleles. This research informs the forensic community on the most effective way to collect and process trace amounts of biological material from brass ammunition and similar evidence.

Flow synthesis development and photocatalytic activity optimization of copper oxide nanoparticles using design of experiments

Many studies have focused on reducing the impact of carbon dioxide (CO2) on climate change. A promising approach for CO2 utilization is to use a photocatalyst to activate CO2 and generate valuable chemical compounds. One of the most commonly synthetized photocatalysts is cuprous oxide (Cu2O); however, low efficiency and fast deactivation still limit its industrial application. Here, a batch synthesis in nonaqueous media of Cu2O containing small amounts of metallic copper (Cu0) is investigated. By adjusting the ratio between Cu2O and Cu0 an enhanced photocatalytic efficiency is obtained. To overcome the deactivation limitations of Cu2O, a flow synthesis is developed that continuously supplies fresh photocatalysts to the reaction environment. The flow synthesis has the potential to allow the separate evaluation of the intrinsic reaction kinetic from the photocatalyst deactivation. This work optimizes the flow synthesis using a design of experiments (DOE) approach coupled with response surface methodology (RSM). The obtained surface responses for the measured factors were highly significant (p-value < 0.01 and R2 > 0.95). This novel methodology makes it possible to identify the optimum process conditions to simultaneously improve photocatalytic performance of the obtained material and reaction productivity. This approach enabled us to obtain in flow a combination of Cu2O/Cu0 photocatalyst and to propose a reaction mechanism and kinetic model for the Cu2O formation. The optimization procedure for flow synthesis proposed here provides an efficient path that can be extended to flow synthesis of a wide range of nanoparticles for photocatalytic applications.

An ingenious synergistic solid lubricant of copper and graphite for exceptional wear resistance of the SCF/PTFE/PEEK composite

In this work, the conventional short carbon fiber (SCF)/polytetrafluoroethylene (PTFE)/polyetheretherketone(PEEK) (SCF/PTFE/PEEK) composite was elected as the matrix, copper and graphite micron flakes were further blended to prepare PEEK self-lubricating composites. At a pressure of 12 MPa and a speed of 0.5 m/s, with a graphite content of 7.5 wt% and copper of 2.5 wt% (Gr7.5Cu2.5), the composite exhibited a COF of 0.23 and the lowest wear rate of 4.1 × 10−7 mm3/Nm. Physicochemical analysis of the worn surface of the steel ring revealed that the introduction of appropriate amounts of copper facilitated the tribo-physicochemical reaction during the rubbing process, which favored the formation of a thin and tough transfer film of Gr7.5Cu2.5 on the worn surface of the steel ring.

Effects of beam shaping on copper-steel interfaces in multi-material laser beam powder bed fusion

Multi-material laser beam powder bed fusion (PBF-LB) is a promising approach to meet industrial demands for multifunctional components, due to its enhanced freedom of design. Copper and stainless steel are interesting materials to be combined due to the high electrical and thermal conductivity of copper and the mechanical strength and wear resistance of steel. However, this system suffers from copper contamination cracking (CCC), a phenomenon which leads to intergranular cracking of the steel due to penetration of liquid copper. The more these materials intermix, the greater the amount of copper that can penetrate and damage the steel. Mixing is more intense when steel is below copper during printing, a situation that cannot always be avoided due to design constraints. In this sense, this research tackles the worst scenario of printing CuCrZr onto 316L and analyses the effect of beam shaping on interface quality. For the first time, a ring-mode laser was applied to multi-material PBF-LB with the goal to reduce intermixing. It was observed that using a ring-mode laser source instead of a Gaussian beam decreases mixing of the two alloys and reduces interface defects, albeit being unable to completely suppress cracking. Grain size and texture were also affected by the beam shape, with the Gaussian beam leading to formation of small equiaxed grains along 20 layers of CuCrZr, resulting in random texture. The ring-mode laser source, on the other hand, yields columnar grains and <100> texture along the build direction. Both beam shapes were observed to induce supercooling below the liquid miscibility gap in the Cu–Fe system. Besides the expected γ-Fe and ε-Cu phases, iron was also found to crystallize in a body-centered cubic (BCC) lattice structure, which is believed to happen due to Ni depletion of the steel in Cu-rich compositions, coupled to insufficient copper within the Fe-rich liquid during solidification. BCC fractions are higher for the Gaussian beam. These differences in microstructure and BCC fraction are attributed to the high intermixing of CuCrZr and 316L when applying Gaussian beams, which is around 10 times higher than with the ring-mode laser.

No- or Low-Content Copper Compounds for Controlling Venturia oleaginea, the Causal Agent of Olive Leaf Spot Disease.

The efficacy of using a synthetic (azoxystrobin + difenoconazole), copper-based (copper oxychloride) and low-content copper compound (copper complexed with gluconate and lignosulphonate) fungicides for controlling Venturia oleaginea, the causal agent of olive spot disease, was evaluated in an olive (cv. Nabali) orchard located in the Kafr Qud area (Palestine) in 2017-2018. Treatments were applied at three different times (February, April, and August). In January 2017, at the beginning of the experiment, about 90% of the leaves grown in 2016 were infected. Defoliation was determined by counting the leaves on the labeled branches initially and then periodically. It increased gradually in both the control and treated trees, but those treated with azoxystrobin + difenoconazole or with copper complexed with gluconate and lignosulphonate showed a slower defoliation rate. During 2017, new shoots grew and new leaves developed. All treatments reduced the drop of new leaves with respect to the control, with positive effects on the reproductive activity (inflorescence growth and yield). Overall, all treatments significantly reduced the disease, thus indicating the possibility of greatly reducing infections if treatments are regularly applied each year, also with traditional (copper-based) fungicides. Due to their capability of penetrating inside the vegetative tissue, azoxystrobin + difenoconazole or copper complexed with gluconate and lignosulphonate reduced/slowed down the drop of infected leaves. The use of these fungicides is therefore particularly recommended when olive leaf spot disease is severe. The use of low-content copper compounds allows the amount of metallic copper used for the treatments against V. oleaginea to be greatly reduced.